CCNA 3 Chapter 8 v5.0 exam answers
1
Refer to the exhibit. Which statement is supported by the output?
A default route is being learned through an external process.
The route to 192.168.1.1 represents the configuration of a loopback interface.
Summarization of routes has been manually configured.
A static default route has been manually configured on this router.
_______________________________________________________________
2
Refer to the exhibit. All networks are active in the same EIGRP routing domain. When the auto-summary command is issued on R3, which two summary networks will be advertised to the neighbors? (Choose two.)
192.168.1.0/30
172.16.0.0/16
172.16.3.0/24
192.168.10.0/24
192.168.10.0/30
_______________________________________________________________
3
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
R1 and R2 could not establish an EIGRP adjacency. What is the problem?
EIGRP is down on R2.
R1 Fa0/0 link local address is wrong.
R1 Fa0/0 is not configured to send hello packets.
R1 Fa0/0 and R2 Fa0/0 are on different networks.
EIGRP is down on R1.
_______________________________________________________________
4
Refer to the exhibit. Considering that R2, R3, and R4 are correctly configured, why did R1 not establish an adjacency with R2, R3, and R4?
because the Fa0/0 interface of R1 is declared as passive for EIGRP
because the IPv4 address on Fa0/0 interface of R1 is incorrect
because the automatic summarization is enabled on R1
because there is no network command for the network 192.168.1.0/24 on R1
_______________________________________________________________
5
Fill in the blank. Do not use abbreviations.
What is the command that should be issued on a router to verify that EIGRP adjacencies were formed?
show ip eigrp neighbor
_______________________________________________________________
6
In which scenario will the use of EIGRP automatic summarization cause inconsistent routing in a network?
when the routers in an IPv4 network have mismatching EIGRP AS numbers
when there is no adjacency that is established between neighboring routers
When the routers in an IPv4 network are connected to discontiguous networks with automatic summarization enabled
when there is no common subnet that exists between neighboring routers
_______________________________________________________________
7
In which IOS CLI mode must a network administrator issue the maximum-paths command to configure load balancing in EIGRP?
interface configuration mode
router configuration mode
privileged mode
global configuration mode
_______________________________________________________________
8
Which command can be issued on a router to verify that automatic summarization is enabled?
show ip eigrp neighbors
show ip protocols
show ip eigrp interfaces
show ip interface brief
_______________________________________________________________
9
Fill in the blank. Do not use abbreviations.
The passive-interface command causes an EIGRP router to stop sending hello packets through an interface.
_______________________________________________________________
10
Refer to the exhibit. A network administrator has configured EIGRP authentication between routers R1 and R2. After the routing tables are reviewed, it is noted that neither router is receiving EIGRP updates. What is a possible cause for this failure?
The same autonomous system numbers must be used in the interface configurations of each router.
The same number of key strings must be used on each router.
The authentication configuration is correct, issue the show ip eigrp neighbors command to troubleshoot the issue.
The same key chain name must be used on each router.
The key string should be used in interface mode instead of the key chain.
_______________________________________________________________
11
Refer to the exhibit. Router R3 is receiving multiple routes through the EIGRP routing protocol. Which statement is true about the implementation of summarization in this network?
Automatic summarization is disabled on R3.
Automatic summarization has been enabled only for the 172.21.100.0/24 network.
Automatic summarization is enabled on neighboring routers.
Automatic summarization is disabled on a per-interface basis.
_______________________________________________________________
12
Two routers, R1 and R2, have established an EIGRP neighbor relationship, but there is still a connectivity problem. Which issue could be causing this problem?
automatic summarization that is disabled on both routers
an authentication mismatch
an access list that is blocking advertisements from other networks
a process ID mismatch
_______________________________________________________________
13
Refer to the exhibit. After the configuration shown is applied on router R1, the exhibited status message is displayed. Router R1 is unable to form a neighbor relationship with R2 on the serial 0/1/0 interface. What is the most likely cause of this problem?
The IPv4 address configured on the neighbor that is connected to R1 serial 0/1/0 is incorrect.
The hello interval has been altered on serial 0/1/0 and is preventing a neighbor relationship from forming.
The network statement used for EIGRP 55 does not enable EIGRP on interface serial 0/1/0.
The networks that are configured on serial 0/0/0 and serial 0/1/0 of router R1 are overlapping.
The passive-interface command should have been issued on serial 0/1/0.
_______________________________________________________________
14
Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.
What action should be taken to solve this problem?
Enable the serial interfaces of both routers.
Configure the same hello interval between the routers.
Configure EIGRP to send periodic updates.
Configure both routers with the same EIGRP process ID.
_______________________________________________________________
15
What is a characteristic of manual route summarization?
has to be configured globally on the router
requires high bandwidth utilization for the routing updates
reduces total number of routes in routing tables
cannot include supernet routes
_______________________________________________________________
16
Which address best summarizes the IPv6 addresses 2001:DB8:ACAD::/48, 2001:DB8:9001::/48, and 2001:DB8:8752::/49?
2001:DB8:8000::/47
2001:DB8:8000::/48
2001:DB8:8000::/34
2001:DB8:8000::/36
_______________________________________________________________
17
Refer to the exhibit. Which two routes will be advertised to the router ISP if autosummarization is disabled? (Choose two.)
10.1.0.0/16
10.1.4.0/24
10.1.4.0/30
10.1.2.0/24
10.1.4.0/28
_______________________________________________________________
18
Which three statements are advantages of using automatic summarization? (Choose three.)
It improves reachability in discontiguous networks.
It maximizes the number of routes in the routing table.
It decreases the number of entries in the routing table.
It ensures that traffic for multiple subnets uses one path through the internetwork.
It reduces the frequency of routing updates.
It increases the size of routing updates.
_______________________________________________________________
19
Refer to the exhibit. Which statement accurately reflects the configuration of routing on the HQ router?
A static default route was learned via EIGRP routing updates.
A static default route was configured on this router.
The IP address assigned to the GigabitEthernet0/0 interface is 172.16.2.0 255.255.255.0.
The static default route should be redistributed using the default-information originate command.
_______________________________________________________________
20
Refer to the exhibit. A network administrator has issued the shown commands. The EIGRP routing domain has completely converged and a network administrator is planning on configuring EIGRP authentication throughout the complete network. On which two interfaces should EIGRP authentication be configured between R2 and R3? (Choose two.)
serial 0/0/1 of R3
gig 0/0 of R3
serial 0/0/1 of R2
serial 0/1/0 of R4
serial 0/1/0 of R2
_______________________________________________________________
21
Refer to the exhibit. Remote users are experiencing connectivity problems when attempting to reach hosts in the 172.21.100.0 /24 network. Using the output in the exhibit, what is the most likely cause of the connectivity problem?
The GigabitEthernet interfaces are not limiting the flow of EIGRP message information and are being flooded with EIGRP traffic.
The hello timer has been modified on interface GigabitEthernet 0/1 of R3 and not on the neighbor, causing a neighbor adjacency not to form.
The passive-interface command is preventing neighbor relationships on interface GigabitEthernet 0/0.
The GigabitEthernet 0/1 interface is not participating in the EIGRP process.
_______________________________________________________________
22
Two routers, R1 and R2, share a 64 kb/s link. An administrator wants to limit the bandwidth used by EIGRP between these two routers to 48 kb/s. Which command is used on both routers to configure the new bandwidth setting?
ip bandwidth-percent eigrp 100 48
ip bandwidth-percent eigrp 75 100
ip bandwidth-percent eigrp 100 75
ip bandwidth-percent eigrp 100 64
ip bandwidth-percent eigrp 64 48
_______________________________________________________________
23
Refer to the exhibit. A network administrator has attempted to implement a default route from R1 to the ISP and propagate the default route to EIGRP neighbors. Remote connectivity from the EIGRP neighbor routers to the ISP connected to R1 is failing. Based on the output from the exhibit, what is the most likely cause of the problem?
The ip route command must specify a next-hop IP address instead of an exit interface when creating a default route.
There are no EIGRP neighbor relationships on R1.
The command default-information originate has not been issued on R1.
The network statement for the ISP connection has not been issued.
The command redistribute static has not been issued on R1.
Refer to the exhibit. Which statement is supported by the output?
A default route is being learned through an external process.
The route to 192.168.1.1 represents the configuration of a loopback interface.
Summarization of routes has been manually configured.
A static default route has been manually configured on this router.
2
Refer to the exhibit. All networks are active in the same EIGRP routing domain. When the auto-summary command is issued on R3, which two summary networks will be advertised to the neighbors? (Choose two.)
192.168.1.0/30
172.16.0.0/16
172.16.3.0/24
192.168.10.0/24
192.168.10.0/30
3
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
R1 and R2 could not establish an EIGRP adjacency. What is the problem?
EIGRP is down on R2.
R1 Fa0/0 link local address is wrong.
R1 Fa0/0 is not configured to send hello packets.
R1 Fa0/0 and R2 Fa0/0 are on different networks.
EIGRP is down on R1.
4
Refer to the exhibit. Considering that R2, R3, and R4 are correctly configured, why did R1 not establish an adjacency with R2, R3, and R4?
because the Fa0/0 interface of R1 is declared as passive for EIGRP
because the IPv4 address on Fa0/0 interface of R1 is incorrect
because the automatic summarization is enabled on R1
because there is no network command for the network 192.168.1.0/24 on R1
5
Fill in the blank. Do not use abbreviations.
What is the command that should be issued on a router to verify that EIGRP adjacencies were formed?
show ip eigrp neighbor
6
In which scenario will the use of EIGRP automatic summarization cause inconsistent routing in a network?
when the routers in an IPv4 network have mismatching EIGRP AS numbers
when there is no adjacency that is established between neighboring routers
When the routers in an IPv4 network are connected to discontiguous networks with automatic summarization enabled
when there is no common subnet that exists between neighboring routers
7
In which IOS CLI mode must a network administrator issue the maximum-paths command to configure load balancing in EIGRP?
interface configuration mode
router configuration mode
privileged mode
global configuration mode
8
Which command can be issued on a router to verify that automatic summarization is enabled?
show ip eigrp neighbors
show ip protocols
show ip eigrp interfaces
show ip interface brief
9
Fill in the blank. Do not use abbreviations.
The passive-interface command causes an EIGRP router to stop sending hello packets through an interface.
10
Refer to the exhibit. A network administrator has configured EIGRP authentication between routers R1 and R2. After the routing tables are reviewed, it is noted that neither router is receiving EIGRP updates. What is a possible cause for this failure?
The same autonomous system numbers must be used in the interface configurations of each router.
The same number of key strings must be used on each router.
The authentication configuration is correct, issue the show ip eigrp neighbors command to troubleshoot the issue.
The same key chain name must be used on each router.
The key string should be used in interface mode instead of the key chain.
11
Refer to the exhibit. Router R3 is receiving multiple routes through the EIGRP routing protocol. Which statement is true about the implementation of summarization in this network?
Automatic summarization is disabled on R3.
Automatic summarization has been enabled only for the 172.21.100.0/24 network.
Automatic summarization is enabled on neighboring routers.
Automatic summarization is disabled on a per-interface basis.
12
Two routers, R1 and R2, have established an EIGRP neighbor relationship, but there is still a connectivity problem. Which issue could be causing this problem?
automatic summarization that is disabled on both routers
an authentication mismatch
an access list that is blocking advertisements from other networks
a process ID mismatch
13
Refer to the exhibit. After the configuration shown is applied on router R1, the exhibited status message is displayed. Router R1 is unable to form a neighbor relationship with R2 on the serial 0/1/0 interface. What is the most likely cause of this problem?
The IPv4 address configured on the neighbor that is connected to R1 serial 0/1/0 is incorrect.
The hello interval has been altered on serial 0/1/0 and is preventing a neighbor relationship from forming.
The network statement used for EIGRP 55 does not enable EIGRP on interface serial 0/1/0.
The networks that are configured on serial 0/0/0 and serial 0/1/0 of router R1 are overlapping.
The passive-interface command should have been issued on serial 0/1/0.
14
Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.
What action should be taken to solve this problem?
Enable the serial interfaces of both routers.
Configure the same hello interval between the routers.
Configure EIGRP to send periodic updates.
Configure both routers with the same EIGRP process ID.
15
What is a characteristic of manual route summarization?
has to be configured globally on the router
requires high bandwidth utilization for the routing updates
reduces total number of routes in routing tables
cannot include supernet routes
16
Which address best summarizes the IPv6 addresses 2001:DB8:ACAD::/48, 2001:DB8:9001::/48, and 2001:DB8:8752::/49?
2001:DB8:8000::/47
2001:DB8:8000::/48
2001:DB8:8000::/34
2001:DB8:8000::/36
17
Refer to the exhibit. Which two routes will be advertised to the router ISP if autosummarization is disabled? (Choose two.)
10.1.0.0/16
10.1.4.0/24
10.1.4.0/30
10.1.2.0/24
10.1.4.0/28
18
Which three statements are advantages of using automatic summarization? (Choose three.)
It improves reachability in discontiguous networks.
It maximizes the number of routes in the routing table.
It decreases the number of entries in the routing table.
It ensures that traffic for multiple subnets uses one path through the internetwork.
It reduces the frequency of routing updates.
It increases the size of routing updates.
19
Refer to the exhibit. Which statement accurately reflects the configuration of routing on the HQ router?
A static default route was learned via EIGRP routing updates.
A static default route was configured on this router.
The IP address assigned to the GigabitEthernet0/0 interface is 172.16.2.0 255.255.255.0.
The static default route should be redistributed using the default-information originate command.
20
Refer to the exhibit. A network administrator has issued the shown commands. The EIGRP routing domain has completely converged and a network administrator is planning on configuring EIGRP authentication throughout the complete network. On which two interfaces should EIGRP authentication be configured between R2 and R3? (Choose two.)
serial 0/0/1 of R3
gig 0/0 of R3
serial 0/0/1 of R2
serial 0/1/0 of R4
serial 0/1/0 of R2
21
Refer to the exhibit. Remote users are experiencing connectivity problems when attempting to reach hosts in the 172.21.100.0 /24 network. Using the output in the exhibit, what is the most likely cause of the connectivity problem?
The GigabitEthernet interfaces are not limiting the flow of EIGRP message information and are being flooded with EIGRP traffic.
The hello timer has been modified on interface GigabitEthernet 0/1 of R3 and not on the neighbor, causing a neighbor adjacency not to form.
The passive-interface command is preventing neighbor relationships on interface GigabitEthernet 0/0.
The GigabitEthernet 0/1 interface is not participating in the EIGRP process.
22
Two routers, R1 and R2, share a 64 kb/s link. An administrator wants to limit the bandwidth used by EIGRP between these two routers to 48 kb/s. Which command is used on both routers to configure the new bandwidth setting?
ip bandwidth-percent eigrp 100 48
ip bandwidth-percent eigrp 75 100
ip bandwidth-percent eigrp 100 75
ip bandwidth-percent eigrp 100 64
ip bandwidth-percent eigrp 64 48
23
Refer to the exhibit. A network administrator has attempted to implement a default route from R1 to the ISP and propagate the default route to EIGRP neighbors. Remote connectivity from the EIGRP neighbor routers to the ISP connected to R1 is failing. Based on the output from the exhibit, what is the most likely cause of the problem?
The ip route command must specify a next-hop IP address instead of an exit interface when creating a default route.
There are no EIGRP neighbor relationships on R1.
The command default-information originate has not been issued on R1.
The network statement for the ISP connection has not been issued.
The command redistribute static has not been issued on R1.
No hay comentarios:
Publicar un comentario